设为首页收藏本站

科技网

[技术] 一艘小船建造

[复制链接]
 楼主| 发表于 2013-9-18 09:07:26 | 显示全部楼层

造船

造船

All rem boards are fixed. It remains to shape the upper edge.

造船

造船

Rem is finished.

造船

造船



 楼主| 发表于 2013-9-18 09:07:57 | 显示全部楼层
The straight piece of wood of about 1,3 m shows the flat bottom.

造船

造船

“Bottenband” is fixed at this stage. I didn’t have wood grown to shape, so I used straight grown wood, but a bit oversized.

造船

造船



 楼主| 发表于 2013-9-18 09:08:34 | 显示全部楼层
The axe is quite small, 32 cm included the shaft. The total weight is 750 g. I think the head is 600 g.

造船

造船



Some pictures of the “underrenning”.

造船

造船



造船

造船


 楼主| 发表于 2013-9-18 09:09:01 | 显示全部楼层

造船

造船



造船

造船

One of the boards was attacked by bugs, something I didn’t noticed until after the board was fixed. The hole was initially filled with wood dust and was difficult to spot. Since the tunnel is only at the outside I left it like this. A memory from the year I was attacked by bugs. I had to treat all my stock with some stuff to get rid of the bug or at least try to reduce the amount of them. I spent about a month and a couple of thousand dollars to do so. I had about 100 planks in stock.

造船

造船



 楼主| 发表于 2013-9-18 09:09:41 | 显示全部楼层
Next board is “roterenning”. The two aft is tested on.

造船

造船

The two fore is ready for riveting.

造船

造船

A lot of clamps were needed to keep the board in place.

造船

造船

The upper edge is roughly shaped using an axe.


 楼主| 发表于 2013-9-18 09:10:09 | 显示全部楼层

造船

造船

The upper edge is finished and it is time for the “bandskaut”. There are four of them roughly shaped.

造船

造船

“Bandskautene” are finished, fixed and cut at 90 degrees angel to the “roterenning” board.

造船

造船



 楼主| 发表于 2013-9-18 09:10:46 | 显示全部楼层
“Nyr-odden” is four small pieces of wood on top of the “roterenning”. Two at the stem and two at the stern. I didn’t have drawing of them, so I looked at available pictures and tried to figure out how they should be. Though, some overall dimensions are mentioned in the books.

造船

造船


造船

造船



 楼主| 发表于 2013-9-18 09:11:24 | 显示全部楼层
Two “rip” board ready to be fixed and "ripe" finished.

造船

造船



造船

造船

“Vater” board in progress.


 楼主| 发表于 2013-9-18 09:11:57 | 显示全部楼层

造船

造船


造船

造船

Front view.

造船

造船

 楼主| 发表于 2013-9-18 09:12:25 | 显示全部楼层
“Skott-regle” is a board on top of the ripe from the “keipe” to the stern. Two ribs and a pole support each “skott-regle”. It is also possible to see how the “bete” and knees are made. No grown wood to shape at all. Of course the knees, at least, should have been grown to shape. But I didn’t have any stock. The two set of knees (kne) give the name to the boat: “to-kne f?ring”. The most common size, about two feet longer, have three sets.The support under the "bête" increases the overall strength of the boat and act as a support for “fiskefj?lene”; all according to the books.

造船

造船



造船

造船


造船

造船


您需要登录后才可以回帖 登录 | 注册

本版积分规则

辽公网安备 21100402204006号|科技网 ( 辽ICP备07501385号-1   

GMT+8, 2019-8-19 01:37

Powered by tech-domain X3.4 Licensed

© 2001-2017 Comsenz Inc.

快速回复 返回顶部 返回列表