设为首页收藏本站

科技论坛

 找回密码
 注册
查看: 6403|回复: 22

[技术] 一个新的小车床

[复制链接]
发表于 2014-11-1 09:00:36 | 显示全部楼层 |阅读模式
这个小车床购买的散件,自己组装,就象电脑组装机一样自己按照说明安装。当然也给喜欢DIY爱好者带来一定的快乐。

一个新的小车床

一个新的小车床

The 1023 mounting board. Any way of holding the bed will help.

一个新的小车床

一个新的小车床

I taped tinfoil to the surface to protect it from the slurry I used in lapping. This is not mandatory, just trying it out.

 楼主| 发表于 2014-11-1 09:01:12 | 显示全部楼层

小车床

小车床

Mounting screws through the board.

小车床

小车床

Sticking out.

小车床

小车床

The bed.
 楼主| 发表于 2014-11-1 09:01:33 | 显示全部楼层

小车床

小车床

Hardware.

小车床

小车床

Remove the carriage.

小车床

小车床

Rack in place. Check for burrs inside the rack. Run the rack back and forth inside the channel to dislodge any other burrs, dirt, etc. Screw the rack to the lathe.
 楼主| 发表于 2014-11-1 09:01:56 | 显示全部楼层

小车床

小车床

Always (generally) use the short end of the allen wrench to tighten.

小车床

小车床

Sliding in the rack protector.

小车床

小车床

It wedges in the thin dovetails. Bits of plastic will shave off of the edges.
 楼主| 发表于 2014-11-1 09:02:19 | 显示全部楼层

小车床

小车床

Prop everything on edge. Or just hold it. You do sort of need three hands at this point.

小车床

小车床

Screwdriver...

小车床

小车床

Putting square nuts in place.
 楼主| 发表于 2014-11-1 09:02:53 | 显示全部楼层

小车床

小车床

Mounted.

小车床

小车床

Slide the carriage on and loosen the gib adjustemnt lock screws.

小车床

小车床

Tighten the screws evenly so that it slides but has no play.
 楼主| 发表于 2014-11-1 09:03:54 | 显示全部楼层

小车床

小车床

The thumbscrew should lock the carriage when tightened, but allow it to slide when loose.

小车床

小车床

On to the cross slide.

小车床

小车床

Loosen the gib locking screws.
 楼主| 发表于 2014-11-1 09:04:15 | 显示全部楼层

小车床

小车床

Loosen the gib screws.

小车床

小车床

Slide the slide off and remove the gib.

小车床

小车床

Screw the screws in - this will remove any burrs left in the hole.
 楼主| 发表于 2014-11-1 09:04:39 | 显示全部楼层

小车床

小车床

Adjust the gib screws. The gib locking screws should be slack.

小车床

小车床

Snug up the gib locking screws, this may take several iterations as this usually tightens things up a bit, and then you have to adjust the gibs again.

小车床

小车床

The cross slide screw assembly. Unscrew the lead screw nut (left hand).
 楼主| 发表于 2014-11-1 09:05:00 | 显示全部楼层

小车床

小车床

There is usually a burr in the hole and the nut post may be a bit tight, some creative deburring will make assembly easier.

小车床

小车床

Deburred.

小车床

小车床

The mounting hole and the nut, you want the long end facing away from the front of the lathe.
您需要登录后才可以回帖 登录 | 注册

本版积分规则

辽公网安备 21100402204006号|科技论坛 ( 辽ICP备07501385号-1   

GMT+8, 2018-12-18 02:19

Powered by tech-domain X3.4 Licensed

© 2001-2017 Comsenz Inc.

快速回复 返回顶部 返回列表