设为首页收藏本站

科技论坛

 找回密码
 注册
查看: 21193|回复: 222

[技术] 尼克的车床和铣床

[复制链接]
发表于 2014-7-29 05:57:24 | 显示全部楼层 |阅读模式
尼克的车床和铣床
这个老外的东西实在是太好了,不转过来,实现是太遗憾了。绝对是精品呀。相信国人不会有如此精的小车床和小铣床了。所以必须转过了与大家分享。由于是英文的,翻译工程太大,所以,还是原文吧。唯一的遗憾。


 楼主| 发表于 2014-7-29 06:04:35 | 显示全部楼层
Mike Wooten’s Lathe And Custom Motor Mount
Mike Wooten sent these pictures of his lathe and custom motor mount.



车床和铣床

车床和铣床

车床和铣床

车床和铣床
 楼主| 发表于 2014-7-29 06:08:37 | 显示全部楼层
Ken Klamm adapted a Taig tailstock to his old Unimat lathe.

车床和铣床

车床和铣床


车床和铣床

车床和铣床


车床和铣床

车床和铣床


 楼主| 发表于 2014-7-29 06:10:01 | 显示全部楼层
Karl Harnish's New Handle For His Taig Tailstock
“My Taig is on a large board that just sits on my workbench and it has occasionally moved if I put too much pressure on the original handle, so I thought I would try for a handle that will allow a push and a pull at the same time to see if that would help. (I guess I could learn how to sharpen my drill bits, or at least buy new ones.)
I started with an eighth by half mild steel and duplicated the holes from the original steel, then cut the new piece to length, leaving about 2.5 to 3 inches beyond each hole.
I put a piece of 1 inch wooden dowel rod in the milling attachment/vice, and using an eighth inch Dremel burr in the collet, I cut a blind slot about 3/4 inch deep, as long as the cross slide travel would allow. My idea was to try to get the center of the steel in about the center of the wood. Once the slots were cut, I cut off the dowel at one edge of the slot and cut the other end leaving a 6 and a half inch piece and a 5 and a half piece. A little time on the sanding wheel eased the edges Again, using the milling attachment and vice, I drilled and counter sank the holes in the wood, more or less an inch apart, slightly beyond the slot to allow for the 8-32 x 1/2 socket flat head screws to bottom out in my counter sunk holes. Then I fit the steel into the slot, and tapped it tight to the bottom and end of the slot and marked where I needed to drill the holes in the steel. The steel was then drilled and tapped for 8-32 machine screws. I didn't see much sense in the bolt and nut to hold the original handle in place, and the cotter pin was a nuisance, so I turned the "belaying" pins to hold the handle in place. I made the one that goes through the 2 straps a bit thicker to accommodate the larger holes in bracket. (It bothered me to have the original handle flopping around if I disconnected the cotter pin and left the bolt attached. With the 2 pins, it's a cinch to completely remove the handle when I am using a dead center on the tailstock.
I bit of stain and 3 coats of rub on poly on the wood and done.”

车床和铣床

车床和铣床

车床和铣床

车床和铣床

车床和铣床

车床和铣床
 楼主| 发表于 2014-7-29 06:11:07 | 显示全部楼层
Karl also sent these pictures of a Taig made button for his jeans.

车床和铣床

车床和铣床


车床和铣床

车床和铣床


 楼主| 发表于 2014-7-29 06:12:30 | 显示全部楼层
Jack Bonofey’s Taig Chuck On His Prazi Lathe
Jack Bonfoey mounted a Taig chuck on his Prazi lathe:
“Here is the story and a few pictures of the Taig chuck on my Prazi SD-300 lathe.  
By the way, this is the link to the yahoo group where this started:http://groups.yahoo.com/neo/grou ... ations/messages/161
I wanted a 4-jaw independent chuck for my older Prazi SD-300 lathe, but I don't believe you can buy one any longer. I heard some folks where having a "register" (recess) cut into the back of a Taig 1030 chuck and adding studs to mount it like the Prazi 3-jaw chuck. There is a person in United Kingdom who will do this, but with shipping and difference in exchange rate it would have been over $200 (half of what I paid for the used lathe).
So, I got the idea to buy an 2MT to 3/4"-16 arbor from Little Machine Shop and just screw on the Taig 1030 chuck. I happened into your website when searching for a Taig chuck, and I've been pleased with the support I've got from you. I also liked the quite affordable Taig accessories that screw-on to the 3/4"-16 spindle.
I put it all together today and it had a little over .003" run out on the face of both the chuck and the face plate. So, I took your good advice and did a very light facing cut on the arbor right where the chuck and face plate mount. In the attached arbor picture the cut would be right on the nut portion of the arbor facing the camera. Then it went down to less than .001" run out, which is more accurate than about anything I can do.”

车床和铣床

车床和铣床


车床和铣床

车床和铣床


 楼主| 发表于 2014-7-29 06:14:35 | 显示全部楼层

车床和铣床

车床和铣床


车床和铣床

车床和铣床


车床和铣床

车床和铣床


 楼主| 发表于 2014-7-29 06:17:06 | 显示全部楼层
Chris Smith's Taig Lathe Projects

车床和铣床

车床和铣床

Wood handles for the carriage and cross slide

车床和铣床

车床和铣床


车床和铣床

车床和铣床



 楼主| 发表于 2014-7-29 06:17:59 | 显示全部楼层

车床和铣床

车床和铣床

His Taig based wood lathe

车床和铣床

车床和铣床



 楼主| 发表于 2014-7-29 06:19:01 | 显示全部楼层
Violin pegs

车床和铣床

车床和铣床


车床和铣床

车床和铣床


车床和铣床

车床和铣床

Drill press modifications
您需要登录后才可以回帖 登录 | 注册

本版积分规则

辽公网安备 21100402204006号|科技论坛 ( 辽ICP备07501385号-1   

GMT+8, 2018-10-18 11:15

Powered by tech-domain X3.4 Licensed

© 2001-2017 Comsenz Inc.

快速回复 返回顶部 返回列表