设为首页收藏本站

科技网

[技术] 自制夹具

[复制链接]
发表于 2014-5-27 03:48:24 | 显示全部楼层 |阅读模式
自制夹具

自制夹具

自制夹具

I was thinking about building bar clamps before I built my long reach C-clamps. But then I thought about making my clamps unique by giving them a long reach, and C-clamps were much easier to make sturdy enough for that. I was still planning to build some bar clamps eventually, but when I visited John Heisz, I saw these clamps so he beat me to it!
The design of these clamps is very close to what I was thinking of building myself.

自制夹具

自制夹具

Made of wood, the clamps are very light. John intended these clamps to be his "overflow" clamps. Basically, these would be the clamps to go to when doing a glue up, and all other clamps are already used up.
He painted them red because otherwise the clamps are hard to spot among other bits of wood in the shop. Same reason I painted my C-clamps.

 楼主| 发表于 2014-5-27 03:48:54 | 显示全部楼层

自制夹具

自制夹具

Just like my C-clamps, these clamps rely on a nut in either side of the piece of wood. But instead of cutting a hexagonal hole, John just glued them in place. Although that could become an issue with wood shrinkage and expansion - if the nuts are rigidly mounted in the wood, they could end up binding on the screw thread when the wood between them shrinks or expands from humidity changes. It's a simpler solution than my solution though, but on my clamps, the nuts were so large that if I had drilled a round hole to fit them in, I would have drilled away almost all the wood.

自制夹具

自制夹具

The upper part of the clamp can tilt to move it from one notch to the next. With the notches about 4 cm (1.5") apart, you often have to turn the handle quite a few turns to set the clamp to the right opening - a similar nuisance as with C-clamps. That is one thing that is convenient about regular bar clamps - just close them on the piece to clamp, and then a few turns tightens them. If or when get around to building some bar clamps of my own, I'll try to put the notches closer together. Very useful to be able to play with John's clamps to experience this!
 楼主| 发表于 2014-5-27 03:50:00 | 显示全部楼层

自制夹具

自制夹具

John used a 3/8" threaded rod, whereas I used 1/2" (mostly to get a coarser thread). Where I used my angle grinder/drill press trick to cut a neck on the end of the screw, John just welded a nut onto the end of his threaded rods. The nut turns inside a cavity in part of the clamp, but with that part of the clamp reaching around the bar, there's no risk of the pad turning on the wood. A clever solution.

自制夹具

自制夹具

The ends of the clamps are made by sandwiching three layers together - easy to make that way. John used LePage PL construction adhesive (the kind of glue that comes in caulking gun tubes), which he's come to swear by. John says:
" Advantages are very high strength - if not as strong as yellow wood glue, it has other very attractive features that counterbalance this, such as longer open time, superior gap filling, doesn't drip off, will adhere to other materials (such as steel hex nuts) and it's very easy to clean up squeeze out once dry. It also has an attractive quality for work on pieces that have a fine finish: it does not creep, like carpenters glue will. Previously, using hide glue was about the only reasonable option if you wanted to avoid cold creep glue lines "
I wasn't fully convinced, but John had some very short cutoffs from making these clamps lying around, and they were surprisingly hard to break. They did break along the glue lines though, whereas with wood glue, the break often wanders from the glue line. John has since done a test and made a video of it.
 楼主| 发表于 2014-5-27 03:50:42 | 显示全部楼层

自制夹具

自制夹具

John also has a SketchUp model for the clamps:
"Attached is the SketchUp model I did during the final stages of construction, mainly to work out some of the details. The small dadoes in the side pieces of the head and screw stock are not only for added strength, they are very important for alignment - setting the screw stock to the correct angle and the head at 90 degrees. The slots may be closer together but that increases the risk of fracture, especially if dropped. I first considered saw tooth notches but settled on these as easier to cut accurately. "
发表于 2014-5-27 15:45:56 | 显示全部楼层
非常不错:lol
发表于 2014-8-28 00:56:43 | 显示全部楼层
路过的帮顶
发表于 2014-11-14 07:33:16 | 显示全部楼层
我是个凑数的。。。
发表于 2015-1-22 17:51:49 | 显示全部楼层
LZ帖子不给力,勉强给回复下吧
发表于 2015-2-6 13:54:56 | 显示全部楼层
真牛逼:victory::victory::victory::victory:
发表于 2015-2-6 13:54:59 | 显示全部楼层
真牛逼:victory::victory::victory::victory:
您需要登录后才可以回帖 登录 | 注册

本版积分规则

辽公网安备 21100402204006号|科技网 ( 辽ICP备07501385号-1   

GMT+8, 2019-3-27 09:27

Powered by tech-domain X3.4 Licensed

© 2001-2017 Comsenz Inc.

快速回复 返回顶部 返回列表