设为首页收藏本站

科技网

1/72蓝背鱼潜艇模型制作

2018-2-11 19:17| 发布者: dymodel| 查看: 1345| 评论: 0|原作者: highboy

摘要: 这里的顶端鉴于计划扩大,以1:72的规模。 The DE standard 3 inch WTC is a perfect match.该D和E标准的3英寸的世台会是一个完美的匹配。 Short enough WTC to move the ballast area forward enough for good level ...
这里的顶端鉴于计划扩大,以1:72的规模。 The D&E standard 3 inch WTC is a perfect match.该D和E标准的3英寸的世台会是一个完美的匹配。 Short enough WTC to move the ballast area forward enough for good level trim.短期足够的世台会动议镇流器领域提出足够的良好水平,修剪。 
  You can se the size of this boat next to Darrin's 1:32 23 I'm building.您可以在本身的大小,这船旁边的darrin的1点32分23我的建设。 Not quite a pocket sub but what the hell.不太口袋子,但什么地狱之路。 
  Should still be good in the pool though.应仍然良好,在游泳池虽然。 
  Just got back from the hobby shop and bought a bunch of balsa.刚回来,从嗜好店买了一大堆balsa 。 If you ever built a boat or plane this way you know the method.如果您以往任何时候都建起了船或飞机通过这种方式,您知道的方法。 The halves of the hull will be built top and bottom over an exact profile.该部分的船体将兴建的顶部和底部超过1确切的个人资料。 Half round formers with stringers.半轮成形与迈出。 And then I'll plank the hole thing.然后我将木板洞的事。 Deck will be added after that.甲板上,将补充后。 Fill sand.填补砂。 Glass and fill sand again.玻璃砂,并填写一次。 Then the mold.然后模具。 
  Building pictures next!建设图片未来! 
  Steve史蒂夫 
  

  首先,我采取了顶视图以来,船民是圆的和折叠,它在半地看到,如果这些海军计划分别为对称。 They weren't!他们不是! 
  Then I evened them up.然后我,最终他们。 Took two 1/8 pieces of balsa and used 3M 77 to temporarily hold them together.花了两年的1 / 8件balsa和使用3个月77暂时搁置起来。 Used the same 3M to stick on the plan top view.使用相同的3个月坚持该计划的顶视图。 As you can see I marked all the former positions.正如您所看到的i显着所有前的立场。 
  I then used the scroll saw and cut to the outside of the line on the plan.然后我用滚动看到和削减向外界该行就这一计划。 Once cut I sanded the edges even to the plan line and removed the plan.一旦削减i沙化的边缘,甚至计划路线,并取消该计划。 Next I separated the to sheets of balsa.接下来,我分离,以张balsa 。 
  Marked center line and the former positions.标志着中线和前的立场。 
  After that it's easy using a compass to make the formers on more 1/8 balsa accounting for the 1/16 planking that I will eventually use and the 1/8 balsa of the profile pieces keeping the geometry in check.之后,人们很容易使用一个罗盘,使成型更多的1 / 8 balsa会计为1 / 16 planking ,我最终将使用和1 / 8 balsa该配置文件的保存件的几何形状在检查。 
  More tomorrow folks.明天的乡亲。 
  Steve史蒂夫 
  

  

  

  

  

  

  

  


鲜花

握手

雷人

路过

鸡蛋

辽公网安备 21100402204006号|科技网 ( 辽ICP备07501385号-1   

GMT+8, 2019-11-14 17:55

Powered by tech-domain X3.4 Licensed

© 2001-2017 Comsenz Inc.

返回顶部