设为首页收藏本站

科技网

科技网 门户 新能源 水力发电 查看内容

微水电建造

2018-4-22 20:41| 发布者: dymodel| 查看: 327| 评论: 0|原作者: 风力发电

摘要: 微水电建造 该项目进展缓慢。我是用一个2匹3相电机。我去的阿美特克38伏有刷永磁电机,这是我的风力涡轮机。风暴把它从今年春天。打破了叶片中的一个,所以我没拿时间来修复并重新安装。是很好看,再加上我有一个 ...
微水电建造

该项目进展缓慢。  我是用一个2匹3相电机。我去的阿美特克38伏有刷永磁电机,这是我的风力涡轮机。风暴把它从今年春天。打破了叶片中的一个,所以我没拿时间来修复并重新安装。是很好看,再加上我有一个备用。我已经下到我爸的很多今年。他是81,所以我上班坐在拖拉机上他。上工作了很多过去的每一年。我不知道哪个会先来。他或农场全部A 100。他正在努力他最好使它的拖拉机。他已经有它超过40年。虽然我帮他清理漏油的方法(2)我们的湖泊几次。地段的雨水和其他的东西。只有一个已经运行过,除非下大雨,仍然有足够的水,以填补6''管离开湖边。正如我在过去曾经说过,我打算使用3吋或4''管。也许3'' 2运行2个单位。水变低2,关一关。大坝的最低点约100英尺运行。(+ / - )我有分寸的。我还没有测头,但它是大约20到25英尺。也许30英尺。这是我为我的第一次考验。它看起来并不像很多我知道。我会画它,使它看起来更好。它将被安装到躺在它的身边工作。我会为电机罩,以保护它的元素.. 我测试的角度与最佳/最快的旋转空气软管,这是我所知道的唯一的方式得到一个起点。用螺栓和垫片一些,如果需要,我可以调整角度。刀片是塑料风机叶片。我已经看过很多事情,这看起来是有希望的。这就是不买东西给它做。这是6 1/2'' 3'',我使用的是风力涡轮机在同一个凉棚。该管道是1 1/4'',它夷为平地,在最后做出一个喷嘴1/4近3''宽,我会从3吋或4''管下降到1 1/4 ''在最后。我有很多方法可以尝试,使1/4''壶嘴更大或更小。靠近或远离父亲。更大的管嘴或更小。不同的电机/一族。我将发布更多的时候我得到安装的东西。安装过程可能需要一些时间。就像我说的这个是缓慢的。感谢您的帮助和关闭的电路板给这个项目
以上google翻译

接着来原文
This project has been slow.  I was to use a 2 HP 3 Phase motor. I went with the Ametek 38 volt brushed PM motor that was my wind turbine.A storm took it out this spring. Broke one of the blades so I did not take the time to repair and reinstall it. Was nice to watch.Plus I have a spare.I have been going down to my dad's a lot this year. He is 81 so I work on his tractor for him. Work on it a lot more each passing year. I don't know which will go first.Him or the Farm All A 100. He is trying his best to make it the tractor. He has had it for over 40 years.While there I helped him clean out the spill ways ( 2 ) to our lake several times.Lot's of rain and other things. Only one has run off unless it rains hard.There is still enough water to fill a 6 '' pipe leaving the lake. As I have said in the past, I plan to use 3'' or 4'' pipe. Maybe 3'' with 2 runs for 2 units. 
Water gets to low for 2, Shut one off.To the lowest point of the dam is about 100 feet run. ( +/- ) I have measured this.I have not measured the head but it is around 20 to 25 feet. Maybe 30 feet.This is what I made for my first test. 
 
It does not look like much I know. I will paint it to make it look better.It will be mounted to lay on it's side to work. I will make a cover for the Motor to protect it from the elements..
 
I tested the angle for the best / Fastest rotation with an air hose. It was the only way I knew of to get a starting point.With the bolt and some shims I can adjust the angle if needed.
 
The blade is a plastic blower blade. I have looked at many things and this looks to be promising.That is without buying something made for it. It is 6 1/2 '' by 3''.I used the same arbor that was on the wind turbine. The pipe is 1 1/4''. It is flattened out at the end to make a spout 1/4 by near 3'' wide.I will go from 3'' or 4'' pipe down to the 1 1/4'' at the very end. I have a lot of ways to try.Make the 1/4'' spout BIGGER or smaller. Closer or father away.Bigger pipe spout or smaller.Different Motors / Gens.I will post more when I get the thing installed. Installation may take some time. Like I said this one is SLOW.Thanks for the help with this project given on and off the board.

鲜花

握手

雷人

路过

鸡蛋
上一篇:微水电----HYDRO下一篇:水力发电

辽公网安备 21100402204006号|科技网 ( 辽ICP备07501385号-1   

GMT+8, 2019-4-21 04:48

Powered by tech-domain X3.4 Licensed

© 2001-2017 Comsenz Inc.

返回顶部