科技论坛

 找回密码
 注册
楼主: highboy

[技术] 1/72蓝背鱼潜艇模型制作

[复制链接]
 楼主| 发表于 2008-6-9 06:58:20 | 显示全部楼层
没有多久,或多少重量或泡沫修剪她。
  Now to wait a bit for the expoxy to dry that holds 4 small pices of foam in place and lets see how she sails.现在只要稍微等候,为环氧干拥有四小pices泡沫在地方,并让看到她是如何帆。 That is if it dosen't rain.这是如果它的doesn't雨。
  There's a storm over head now and it's supposed to rain.有一个风暴的头部,现在和它的假定雨。 Go figure.去的数字。
  Anyway.总之。 We'll see.我们将拭目以待。
  Steve史蒂夫
  

  

  她裁剪完美的,然后它开始拖曳她的尾巴。 Turned out one of the lead shot bags came lose and was sliding back and forth.原来,其中一个带头枪杀袋来失去和被滑动回到来回。
  Broke a scope too as you can see.打破了范围过于正如您所看到的。 No biggy.没有biggy 。 All and all she ran great but my pool is like a large bath tub with no where to turn.所有和所有她遇到的伟大,但我池就像一个大浴缸,没有地方把。
  I'll go to the lake next week and let her run.我会去湖下周让她运行。 She can really move but I got to apply the power smoothly as you can see when I horse it on she leans.她真的可以动议,但我到了申请的权力,顺利地你可以看到,当我马,这对她倾斜。
  David's prop works like a charm.大卫的版权作品一样的魅力。 Not a bad day for the first trim.不是一件坏事天为第一修剪。
  Enjoy:享有以下待遇:
  Steve史蒂夫
  

  Here she is at hover about 2 ft. down在这里,她是在悬停约2英尺下降
  

  And on the surface.并在表面上。

 楼主| 发表于 2008-6-9 07:00:02 | 显示全部楼层
这里的小bugger举行的事情。 I must get a lath even a small one for stuff like this.我必须得到板条,甚至一小一为这样的东西。 but a model airplane spinner, a bit of plumbers putty and a piece of aluminum tubing and this is just right.但模型飞机微调,有点水喉匠腻子和一块铝油管,这是恰恰好。
  The depression is for drilling out a hole to fit your 3/16 bearing.抑郁症是钻探出一个洞,以适合您的3 / 16轴承。 Mold is made and I will cast up all of them tomorrow.模具是和我会投了所有他们的明天。
  Then I can ship.然后我还可以提供配送服务。 So far Jason (who didn't have too) sent in his shipping money.到目前为止,贾森(谁没有过)发出在他的航运钱。 I posted that information a few pages back .我张贴的资料,几页回。 Take a look.考虑一下。 It covers the US, Canada, UK, Australia and Japan.它涵盖美国,加拿大,英国,澳洲和日本。
  Steve史蒂夫
  

  一个下午,由约翰安德森哪里赫克做舱壁路要走。 Good question John and dumb ass here over looked that important little step.良好的问题,约翰和哑巴驴在这里期待这一重要的小步骤。
  So to correct an error here's how it goes.因此,以纠正一个错误,这里的如何这是不言而喻的。
  On the first picture this measurement is from the bow to bulk head number one.对第一张图片,这是测量从船头到批量头的数目1 。 It goes just inside the first weld ring where the bow section meets the center section.这是不言而喻内的第一环焊缝的地方低头节会见的中心部分。 Or use the measurement seen here.或使用的测量在这里看到的。
  

  Next we measure from the bow bulkhead to the center section bulkhead.其次,我们的措施,从船头舱壁该中心的第舱壁。 If you count the weld rings from the front it's dead center between the 6th and 7th ring.如果您指望焊缝戒指,从前面,它的死亡中心之间的第六和第七环。 Or use the tape measure location.或使用卷尺的位置。
  

  The next one goes two weld rings aft from the forward end of the stern section or use the measurement.未来一,云二焊缝戒指,从尾部向前年底严峻节或使用的测量。
  

  You can use the far aft stern bulkheads for the prop shaft bearing mount or use some ABS of PVC sheet to make the bearing mount as I did.您可以使用至今尾部斯特恩舱壁为版权轴轴承安装或使用一些ABS树脂的PVC片材,使轴承装入正如我没有。 If you do use those bulkheads you will find by sliding them back they can only fit one location.如果您确实使用这些舱壁你会发现由滑动他们回来,他们只能适合一个位置。
  

  Hope this clears it up a bit for you guys.希望这个清除起来有点为您的朋友。
  


发表于 2015-11-13 20:52:44 | 显示全部楼层
  佩服  佩服
发表于 2017-10-10 09:34:07 | 显示全部楼层
highboy 发表于 2008-6-9 05:47
这里的顶端鉴于计划扩大,以1:72的规模。 The D&E standard 3 inch WTC is a perfect match.该D和E标准的 ...

值得学习借鉴
您需要登录后才可以回帖 登录 | 注册

本版积分规则

辽公网安备 21100402204006号|科技论坛 ( 辽ICP备07501385号-1    

GMT+8, 2017-12-17 00:52

Powered by Discuz! X3.2 Licensed

© 2001-2013 Comsenz Inc.

快速回复 返回顶部 返回列表