科技论坛

 找回密码
 注册

扫一扫,访问微社区

查看: 5882|回复: 9

[技术] 金属不锈钢电解槽

[复制链接]
发表于 2010-8-18 04:43:57 | 显示全部楼层 |阅读模式
转一个用不锈钢制作的电解槽,这个电解槽无需焊接,制作起来非常容易。

  

  The metal that I used for this Electrolyzer Version 5 is, as always, 18 gauge #316 stainless steel. It is highly resistant to corrosion so I like to use this for all of my electrolysis needs. I have heard that #304 can also be used if you are just planning on using NaOH (Sodium Hydroxide) for your electrolyte. NOTE: NaOH can be found at your local hardware store sold in the drain cleaner section. Look for Red Devil Lye.

  My plates are cut to be 12 x 1.5 inches in size. You will get the best results if you find a place that can sheer your stainless for you. Cutting it on a saw would result in a very sloppy edge with a lot of uneven spots. Sheering is by far the best choice when working with pieces like this. -Unless of course you want to pay hundreds of dollars to have them precision laser cut. But remember, this is built for the "Average Joe" here and dare I say that laser cut would provide basically no improvements over sheered pieces.

  Every piece of metal that you have INSIDE of this electrolyzer should be stainless steel. Again, try for #316 if you can. I get the bolts from the Fastenal company.

 楼主| 发表于 2010-8-18 04:44:38 | 显示全部楼层
Here you are seeing a picture of me drilling the second hole in my stack of plates.

  If you have a good COBALT drill bit, you'll be all set. I recommend using 3/8" stainless (#316) bolts as they should be of sufficient size to handle the current requirements. I stacked the pieces of stainless to do the drilling through all 8 at one time. Doing this, you only need to drill 2 holes per electrolyzer ...and again; NO WELDS required! -Woohoo!

  I'll post all of the dimensions and part numbers for the stainless (from the Fastenal Company) shortly. I need to go eat right now.

  
转孔
  

  
中间的绝缘材料。
 楼主| 发表于 2010-8-18 04:46:27 | 显示全部楼层


  

  
 楼主| 发表于 2010-8-18 04:46:40 | 显示全部楼层
  

  

  
 楼主| 发表于 2010-8-18 04:46:55 | 显示全部楼层


  
不锈钢电解槽
  
 楼主| 发表于 2010-8-18 04:48:50 | 显示全部楼层
  

  

  
 楼主| 发表于 2010-8-18 04:49:07 | 显示全部楼层
  

  

  
 楼主| 发表于 2010-8-18 04:49:31 | 显示全部楼层
  

  

看看制作是不是很容易呀。
发表于 2014-3-10 10:07:55 | 显示全部楼层
看看,什么时候东东。
发表于 2014-10-20 22:57:37 | 显示全部楼层
制作工艺不算复杂,可以自制一个,但是电路呢?
您需要登录后才可以回帖 登录 | 注册

本版积分规则

手机版|辽公网安备 21100402204006号|科技论坛 ( 辽ICP备07501385号-1    

GMT+8, 2017-10-23 08:33

Powered by X3.3 Licensed

© 2001-2017 Comsenz Inc.

快速回复 返回顶部 返回列表